Neue KISS FC Firmware verfügbar

Moin zusammen,

für die KISS V1/V2 und CC (Alias AIO) ist eine neue Firmware verfügbar. Aktuell hab ich die nur über die GUI gefunden.

Update to 1.3RC36c (require GUI 2.0.8 or newer) - https://github.com/flyduino/kiss-gui/releases

- adding support for ESC rotation to support custom orientation of the new 4-in-1 (90° CW/CCW, 180°, Upside Down, Upside Down 90°CW/CCW, Upside Down 180°)

- Add Frsky F-Port support (use UPRT pad) - latest LUA available at https://github.com/flyduino/kissfc-tx-lua-scripts/releases

- fix a bug where in failsafe condition motor wouldn't stop while in Turtle mode

- Dshot telemetry fix (ESC telemetry is always on when using Dshot)

- fix a bug where audio was not working with connected Smartaudio on KISS FC v2

Known problems

- spectrum analyzer of current Betaflight blackbox logger is not working

Moin zusammen,

aktuell haben wir ja die 1.3RC36i. Allerdings findet man die nur noch über die GUI oder direkt auf Github: https://github.com/flyduino/kissfc-firmware/releases

Endlich ist es so weit, neue KISS V2 Firmware in der Version 1.39a

https://github.com/flyduino/ki…C5IPwYoz5yXtDeaKJUiKH6YWw

Update to 1.3RC39a (require GUI 2.0.15 or newer) - https://github.com/flyduino/kiss-gui/releases

• Add support for TBS Unify Smartaudio 2.1
• Add support for TBS EVO Crossfire VTX
• Add support for RX link stats (Crossfire + virtual LQ)
• Add Realpit support (PWM 5 pad)
• Add support for FETtec OneWire (PWM 6 pad)
• Add startmode (PIDs calculate different before takeoff to be able to tilt the quad on ground)

Nicht vergessen auf die neue GUI 2.0.15 upzudaten!!!

Die neue Firmware für den KISS Keychain ist auch schon verfügbar:
https://github.com/fedorcomand…VFhuA8p2aJEcNT5tXnBkA5Z0o

In Facebook wurde eine Testversion der 1.40i veröffentlicht.

RC40i changes:

- Added GPS support (yet telemetry/osd only)

- Runcam pass through added (for SpeedyBee app)

- GPS pass through (for uCenter connection)

- Fixed BB gyro scaling and other compatibility issues

- Add EVO crossfire parameters editor support (latest EVO required)

- Added crossfire router (first fc that supports routing!)

- Added turtle mode safety (works after at least one arming)

- Changed lots in crossfire code

- Changed RX processing code (should be more sensitive and direct)

- Disabled StartAssist

- Added I-term windup killer (no I term until you hit 5% throttle)

- Unify SA fixes

- Added VIRTUAL LQ for non crossfire receivers

- Added Full EVO support for ANY receiver

- KissFC can be used as ANY-RECEIVER->Crossfire relay station

- Added digital RSSI for F-PORT receivers

Small HOWTOs:

GPS:

You can use cheap M8N and newer gpses out of the box, some old once may require some manual

configuration. You will get telemetry to frsky/crossfire and if osd supports it - to OSD.

GPS can be connected to any serial port, just select GPS in advanced serial configuration.

EVO:

This is great VTX and i truly like how it works with kiss / fettec / GPS combo. Evo is fully supported

with ANY receiver. Stick menus and pid changes etc. Well, some testing will not harm,

since TBS just released it to public beta.

You can connect it in 3 ways...

1. To crossfire receiver. In gui - select TBS crossfire EVO

2. To Kiss serial. In gui - select TBS crossfire EVO AND assign VTX to evo serial port.

3. To kiss serial as SA device. In gui - select TBS Smartaudio VTX to evo serial port.

You have to enable crossfire/SA protocol on evo and define stick channels.

Yaw left will bring you to EVO osd menu, once more to crossfire parameters editor.

The firmware is available ONLY in hex for and ONLY here (not in the gui).

I am really curious about your feedback and suggestions. Thank you all for testing and support.

Alex AKA FedorCommander

Findet man in dieser Gruppe:
https://www.facebook.com/groups/907549762675568/

Die FW bekommste noch net über Github.

Alex hat in der FB Gruppe über ein Google drive frei gegeben...

Die Gruppe findest oben in der Beschreibung

So sehen die Files aus:

Bei der V2 einfach im Reiter flashen.
Bei der V1 Bootbutton drücken beim einstecken, dann wirst gefragt...

Welche FC ? V1 oder V2?

Dann hast nen Treiberproblem, Bootbutton drücken und im Gerätemanager nachsehen.

Den STM Treiber von der Flyduiono Seite installieren, dann gehts.

Worstcase kann auch das USB Kabel sein, einfach pauschal erstmal nen anderen nehmen.

Die KISS GUI ist jetzt in der Version 2.0.16 verfügbar:

https://github.com/flyduino/kiss-gui/releases

Bugfixes & Enhancements

• add CPU load graph
• add lipo voltage graph
• update to 2.0.16
• sort graphs

MacOS GUI this time as ZIP to prevent faulty DMG notification due to missing signature

Hi,

RC bedeutet release candidate.... wobei man die RC Releases schon so gut wie final betrachten kann... im Gegensatz zu anderen Systemen.